set adf  <num>


Set ADF  to <num> frequency in a flight plan


set afcontrol <plane><helicopter>


atmospheric rudder control by user on or off. Set off if your flight plan wants to take the stick.


set altitude [alt] <num>


preselect target altitude (m)


set apcontrol <plane> or <helicopter>


Toggle autopilot modes between plane and helicopter


set apmode airfoil


set autopilot control to rudder


set approachentryaltitude <num>


Define the altitude above ground (ground is provided by FSP) to be automatically entered as target altitude when switching to the approach entry point


set approachentrydistance <num>


Define the distance, at which the approach entry point is generated from runway start of selected runway. <num> is distance in nm


set approachentryoffset <num>


Define the angle from runway inbound heading, at which the approach entry point is generated. <num> is offset in deg


set brakepower <num>


sets brakepower to <num> percent (0-100) .Value only valid for this session.


set climb [desc] <num>


preselect climb / sink rate (m/s)


set climb [desc] autoclimb [ac]


preselect autoclimb; set climb rates automatically


set climb [desc] autodescend [ad]


preselect autodescend; set descent rates automatically


set climb wp


set the climb rate to a value that the predefined altitude is hit at the next waypoint


set cmdonly on


if used in the beginning of the flight plan, all actual flying has to be done by the pilot itself


set cmdonly off


switch cmdonly mode off in a flight plan


set com [com1] <num>


Set com1 to <num> frequency in a flight plan


set current utc


set current utc time


set destination <ICAO>


set destination airport


set departure [dep] <ICAO>


set departure airport


set distanceunits <miles><meters>


define units for distances in your flight plan


set fuelpercent <num>


sets fuel level in all tanks to  <num> percent


set gear


gear down during auto landings. Disables “set nogear”. Use “set nogear” to perform auto landings without gear down (waterlandings)


set home airport


Looks up nearest airport and sets it as the home airport for later use. Usually defined on ground at the beginning of a flight plan.


set ils


Set vertical autopilot into the approach mode - equivalent to pressing the ALT and the APR button on the EFIS


set ilsentrydistance <num>


Define the distance, at which the ils entry  entry point is generated from runway start of selected runway. <num> is distance in nm


set maxbank <num>


Set maximum bank angle that FSP uses to turn into a target. 50 would be fighter style (small radius), 25 would be passenger jet style (big radius)


set maxpitch <num>


Set maximum pitch angle that FSP uses to archieve a climb / sink rate


set nav1 <num>


Set nav1 to <num> frequency in a flight plan, f.e. 118.70


set nav2 <num>


Set nav2 to <num> frequency in a flight plan.


set nogear


In planes with floats and wheels, wheels will not be lowered during auto landings. Use “set gear” to switch off.


set origin <ICAO>


set origin airport


set payload <num>


set payload to <num> pounds evenly distributed between all payloadstations of the aircraft


set payloadstation <which> <what>


set payloadstation <which> of current plane with <what> pounds of payload


set radarrange <num>


define the radarrange in the efis to <num> miles


set speed <num>


Set speed value in knots or mach, as required


set speed minimumspeed


as defined in fspilot.ini


set speed approachspeed


as defined in fspilot.ini


set speed cruisingspeed


as defined in fspilot.ini


set speed takeoffspeed


as defined in fspilot.ini


set speed safespeed


Sets an effective cruising speed depending on altitude and aircraft. < FL100: 250 knt; between FL 100 and 180:barberpolespeed* 0.88; > FL 180: barberpolemach * 0.88


set speedunits <knots><meters>


define the units for speed in your flight plan


set throttle <num>


sets the throttle levers to [num] percent


set timeacceleration [timeacc] <num>


speed up or reduce time acceleration within a flight plan

 

set userinput <on><off>


Enable userinput during a flight plan. Otherwise, pressing buttons on the EFIS will be disabled except the screenshot button.


set waypointclimb <num>


Defines the climbrate in ft/min in which the aircraft will climb between waypoints. 


set wphitprecision <num1> <num2>


Define the distance at which FSP switches to the next target (waypoint) in flight plans. <num1> distance below FL 100 in meters, <num2> sistance above FL100 in meters. Both arguments mandatory.


set xpndr [transponder]  <num>


Set the transponder  to <num> frequency in a flight plan

Created with the Personal Edition of HelpNDoc: Easily create EBooks